Finally got around to replacing the last three of my x-10 devices.
The three new devices are:
in line relay 2475s
keypadlinc 2486s
applianceLinc 2456s
Have all three working but am getting the following error in the log when ever anyone is activated.
all other devices are working fine.

Any help would be appreciated

Elwood


Sent INSTEON "Bath Rm Shower" on
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Sent INSTEON "Bath Rm Shower" off
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Sent INSTEON "Bath Rm Sink" on
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Sent INSTEON "Bath Rm Sink" off
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Sent INSTEON "Bath Rm Upper floresent" on
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Sent INSTEON "Bath Rm Upper floresent" off
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined
Error device state key brightnessLevel not defined

Mar 17, 2012 3:36:44 PM
Sent INSTEON "Office" off
Sent INSTEON "Office" on to 100
Sent INSTEON "Office" off
Sent INSTEON "Office" on to 100

Odd, all three of those devices are relay devices which means that they don't have a brightnessLevel state. I wonder if you have a trigger or some action that uses brightnessLevel on those devices and when you swapped them out with the relay versions they started to fail. Check your triggers to make sure there are none that are looking for brightness on those devices.

The fact that you get exactly 10 errors when the device state changes may be a clue. Maybe it's some set of actions.

Jay

The old x-10 devices were also relay type, found no triggers that would activate with the new devices.

On the KPL went to set up and adjusted the LED brightness and that gives the same error.
Also found with all three if I check and uncheck either remote display or comm enabled check box I get the error.

Just to check I added a new lamplinc 2456D that worked with no errors.

I will delete one of the new device and reinstall it to see if that makes any change.


Elwood

Jay

I deleted all three new devices and reinstalled them. I no longer get the error.

Don't know what happened but all seem to be OK now.

Thanks again for always being there.

Elwood

This can also happen if you have a Control Page that inspects the device brightness (either with text or an icon), then the device type is changed to one that doesn't have brightness. In that case, the device control still exists on the Control Page but the state it is trying to show doesn't exist anymore, so you get the errors logged. Deleting the device will fix it, because it deletes those controls from the Control Page.