Hi,

Is there support for the version 42 i2cs engine in Indigo version 5.1.5 ?

I'm having trouble connecting to my 2477S. I'm running Indigo version 5.1.5 using the 2412 or 2413 controller (not sure which) as indicated by the software config setting, but definitely not the 2414.

This is my first 2477S in my installation. I have several other dual band SwitchLincs in my installation, but they are dimmers and the firmware for those are version 40 i2.

The 2477s comes up on the Define Insteon Device screen as version 42 i2cs engine. Indigo and the device seem to communicate as indicated by the active link icon graphic, but fails at the last step.

2012-08-04 17:07:20 PowerLinc Linking - entered discovery linking mode (240 seconds)
2012-08-04 17:07:21 PowerLinc Linking - received module button pressed from 1E.34.3B
2012-08-04 17:07:22 PowerLinc Linking - syncing PowerLinc links (address 0F.E1.1A)
2012-08-04 17:07:22 PowerLinc Linking - . . adding: INSTEON plc link to controller 1E.34.3B, flags 03, group 01, data 00 00 FF
2012-08-04 17:07:22 PowerLinc Linking - . . adding: (not added -- probably already exists)
2012-08-04 17:07:22 PowerLinc Linking - sync complete
2012-08-04 17:07:22 PowerLinc Linking - sending engine version request to 1E.34.3B
2012-08-04 17:07:22 PowerLinc Linking - PowerLinc links updated
2012-08-04 17:07:29 PowerLinc Linking - no response from device
2012-08-04 17:07:29 PowerLinc Linking - sending engine version request to 1E.34.3B
2012-08-04 17:07:29 PowerLinc Linking - received engine version 02 from 1E.34.3B
2012-08-04 17:07:29 PowerLinc Linking - sending id request for device information to 1E.34.3B
2012-08-04 17:07:30 PowerLinc Linking - received id request response from 1E.34.3B
2012-08-04 17:07:32 PowerLinc Linking - initializing remote device "Garage Fan" (address 1E.34.3B, firmware version 42)
2012-08-04 17:07:33 PowerLinc Linking - initialize complete
2012-08-04 17:07:33 PowerLinc Linking - syncing remote device "Garage Fan" (address 1E.34.3B, firmware version 42)
2012-08-04 17:07:34 PowerLinc Linking - syncing all links
2012-08-04 17:08:44 Error failed to fetch data from remote module
2012-08-04 17:08:44 Error Linking - syncing failed
2012-08-04 17:08:44 Error linking failed

I believe that firmware should work without a problem. From the Event Log it looks like it might be a signal problem. Try moving your PowerLinc to a few different outlets (using an extension cord since we are just troubleshooting) to see if you can get it defined with a different signal path.

Also try factory resetting the SwitchLinc.

Ok that's good to know.

I know it's on a different leg that I've done 2 previous installations on.

I'll try verifying it's not the unit but the communication.

C
--

I moved a 2443 Access point onto the same leg I know works with the 2 previous installations and re-synced, and it worked!

btw, thanks for a great product. I have 26 physical devices all working well with the Insteon protocol using Indigo 5.

C
--