Hi,

Something strange started showing up in my logs last night. A copy is below. These are codes that don't exist on my system. Started all of a sudden, and I don't know how to turn it off or stop it.

Any advice?
Thanks,
Rob


Jun 4, 2012 8:56:21 AM
Received X10 all lights off (house code L)

Jun 4, 2012 8:57:37 AM
Received X10 C13 preset dim val of 31
Received X10 C13 preset dim val of 29

Jun 4, 2012 8:58:33 AM
Received X10 J10 hail acknowledge
Received X10 J10 status request
Received X10 J10 status request

Jun 4, 2012 8:59:21 AM
Received X10 J10 status request

Jun 4, 2012 8:59:42 AM
Received X10 J10 preset dim val of 31
Received X10 J10 status request
Received X10 J10 status request

Jun 4, 2012 9:00:50 AM
Received X10 J10 status request
Received X10 J10 status request
Schedule A/C to 74 Degrees AT HOME - Daytime, Weekdays

Jun 4, 2012 9:05:15 AM
Trigger Climate - Update Thermostat Upstairs Set Point Values

Jun 4, 2012 9:08:35 AM
Trigger Barb's Away - set keypad lites OFF
Smartphone Radar "IPhone - Barb" state is now Away.
Sent INSTEON "PowerLinc Interface" off (group/scene 11)
Sent INSTEON "Kitchen General Lights Keypad" off (group/scene 11 cleanup)
Sent INSTEON "Front Hall Ceiling Light Keypad" off (group/scene 11 cleanup)
Received X10 J10 on

Jun 4, 2012 9:13:26 AM
Received INSTEON "Motion Sensor - Stairs" on (button 1)
Received INSTEON "Front Door Trigger" on (button 1)
Received INSTEON "Motion Senoor - Outside Front" on (button 1)
Trigger Speak Motion Outside Front Alert OnDemand

Jun 4, 2012 9:14:04 AM
Trigger Motion Front Entry ON
Action Group Security - statusMessage Front Door Alert
Received INSTEON "Front Door Trigger" off (button 1)
Received INSTEON "Front Door Trigger" on (button 1)
Received INSTEON "Front Door Trigger" off (button 1)

Jun 4, 2012 9:14:25 AM
Received INSTEON "Motion Sensor - Stairs" off (button 1)

Jun 4, 2012 9:14:45 AM
Received INSTEON "Motion Senoor - Outside Front" off (button 1)
Trigger Motion Front Entry OFF
Action Group Security - statusMessage Front Door Alert Unset

Jun 4, 2012 9:15:44 AM
Received X10 J6 status request

Jun 4, 2012 9:19:04 AM
Received X10 J6 status request

Jun 4, 2012 9:21:36 AM
Received X10 C3 preset dim val of 31

Jun 4, 2012 9:26:01 AM
Received X10 all units off (house code P)

Jun 4, 2012 9:35:09 AM
Received X10 J5 status request
Received X10 J5 status request
Received X10 H12 status request

Jun 4, 2012 9:35:51 AM
Received X10 J5 status request

I've had some older X10 modules that started issuing random X10 commands like that as they were starting to fail so that may be the problem. It could also be signal noise that happens to look like X10 traffic to the PowerLinc. Finally, the PowerLinc could be failing also and reporting bogus X10 commands to Indigo.

What should I do first. I don't know why it started all of a sudden, but I'm getting swamped with log entries.

Thanks,
Rob

Process of elimination. I'd start by unplugging or disabling any X10 gear. If you can't physically disable a device (like an X10 in-wall switch) then cut the power to the circuit that it's on. Then if you're not seeing them, start reenabling them one at a time. If you have a separate X10 RF interface then disable that as well.